Consortium Services Wiki

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
======Installing SQL Server 2008 R2======

=====Download=====

Click one of the download links below to install the version appropriate for your architecture.

  * **SQLEXPRWT_x64_ENU.exe** 64-bit version 247.5 MB [[http://download.microsoft.com/download/5/5/8/558522E0-2150-47E2-8F52-FF4D9C3645DF/SQLEXPRWT_x64_ENU.exe|DOWNLOAD]]
  * **SQLEXPRWT_x86_ENU.exe** 32-bit version 235.5 MB [[http://download.microsoft.com/download/5/5/8/558522E0-2150-47E2-8F52-FF4D9C3645DF/SQLEXPRWT_x86_ENU.exe|DOWNLOAD]]

=====Install=====

  - Launch the package, you will then see the contents extracted to a temporary location.{{ :sqlexp01.png?nolink |}}
  - SQL Server Setup checks to determine pre-reqs are installed. If not, you will be prompted to install. Click the each link to go to the download site, download the installer provided there, and install the required software.{{ :sqlexp02.png?nolink |}}
  - The Installation Center will then launch. Click on “New installation or add feature to an existing installation” to start the Installation Wizard.{{ :sqlexp03.png?nolink |}}
  - Accept the license terms. If it then tells you that Windows PowerShell failed or needs to be installed to continue, follow this link and click the large, green **Download** button. [[http://download.cnet.com/Microsoft-Windows-PowerShell-1-0-for-Windows-XP/3000-2070_4-75450849.html|DOWNLOAD]] The download should begin on the next page automatically. If not, refresh the page. Do not click any of the links on this page that say "Start Download" or "Download Now" as these are ads. {{ :sqlexp04.png?nolink |}}
  - Review the features to installed and where SQL Server will be installed. Make any changes that are necessary for your environment. This can be left as it is if you are not sure.{{ :sqlexp05.png?nolink |}}
  - Review the "Named Instance" and change if necessary. The "Instance ID" will automatically match the "Named Instance." **!!Write this name down!!**{{ :sqlexp06.png?nolink |}}
  - Review the credentials that will be used for the services that will be created. Click the **Use the same account for all SQL Server services**. Enter an "Account Name" and "Password" for a user account that will administer the SQL Server. This account must already exist on the system. Click **Ok** and click **Next**.{{ :sqlexp07.png?nolink |}}
  - Choose the **Mixed Mode** Authentication. Enter a password (twice) for the "sa" account. **!!Write this password down if you are installing AppMonitor!!** Continue to add any additional users into the box below if desired and click **Next**.{{ :sqlexp08.png?nolink |}}
  - Review the Error Reporting settings.{{ :sqlexp09.png?nolink |}}
  - That’s it!{{ :sqlexp10.png?nolink |}}

=====Configure=====

  - After successfully installing SQL Server Express, go to **Start > All Programs > Microsoft SQL Server 2008 R2 > Configuration Tools > SQL Server Configuration Manager**.
  - In the left-hand pane, expand the **SQL Server Network Configuration** node and click on **Protocols for [YourServerName]**.
  - In the right-hand pane, right-click on **TCP/IP** and click **Properties**.
  - Under "General" next to "Enable", change the **No** to a **Yes**.
  - Above that, click on the **IP Addresses** tab.
  - Here you will see two more "Enable lines. Change them to **Yes**.
  - At the very bottom of the list, under "IPAll" there is a line that says "TCP Port". Enter 1433 into this the field next to it and click **Ok**. Ignore the warning that follows.
  - In the left-hand pane, click on **SQL Server Services**.
  - Right-click on **SQL Server (YourServerName)** and click **Restart**.
  - After restarting, SQL Server should be ready to use. If you are installing AppMonitor, follow this next guide. [[installing_appmonitor|CLICK HERE]]
Consortium Services Wiki

User Tools

Site Tools

Page Tools
